F10 F10 - Remove TPMS Warning

I have successfully removed all warnings about TPMS from my NAV - HU_CIC / RDC = nicht_aktiv (Thanks shawnsheridan!)

Now Im trying to remove the yellow warning light in the instrument cluster.

Anyone attempted this?

Originally Posted by lifo_1

I have successfully removed all warnings about TPMS from my NAV - HU_CIC / RDC = nicht_aktiv (Thanks shawnsheridan!)

Now Im trying to remove the yellow warning light in the instrument cluster.

Anyone attempted this?

Did you search KOMBI for RDC setting, and if that did not work, remove 2VB from VO and VO Code KOMBI, HU_CIC, and RDC?

Originally Posted by shawnsheridan

Did you search KOMBI for RDC setting, and if that did not work, remove 2VB from VO and VO Code KOMBI, HU_CIC, and RDC?

Ta da!

Kommentar=RDC Ueberwachung (Comment=RDC monitoring)

KOMBI / ST_TYR_TIMEOUT = nicht_aktiv
KOMBI /ST_TYR_ALIVE = nicht_aktiv

I tried those 2 above and it didn't fix. I will try to remove 2VB from vo

Originally Posted by lifo_1

I tried those 2 above and it didn't fix. I will try to remove 2VB from vo

Hmmm...that surprises me that those two did not kill it.

Ok. Try this one too:

KL_PREDRIVE_F10_RPA = nicht_aktiv

If unsuccessful, kill 2VB in your VO, and VO Code HU_CIC and KOMBI. RDC has no coding data, so there is nothing to VO Code there I don't think.

Removed the 2VB and VO coded HU_CIC and KOMBI.

No luck. TPMS warning still present in NAV screen and instrument panel

Originally Posted by lifo_1

Removed the 2VB and VO coded HU_CIC and KOMBI.

No luck. TPMS warning still present in NAV screen and instrument panel

That is almost impossible to believe. Are you sure after you removed 2VB from FA, that before you VO Coded HU_CIC and KOMBI, you loaded that FA (the modified one without 2VB) and activated it, and not the FA read from the car?

So load the xml file with the 2VB option removed and VO code those 2 again?

Originally Posted by lifo_1

So load the xml file with the 2VB option removed and VO code those 2 again?

Yes! That is why removed it. Now when you VO Code the ECU's, it won't enable 2VB like your regular FA that is stored in your car will (assuming you did not go so far as to write the modified FA to the car, and the FA in the car is original).

Just to keep the thread alive I have confirmed with Sean what I did was correct. New FA and VO coded Kombi and HUCIC. Still not luck. Will keep researching

when you remove the 2VB out of the VO, you still need to pulll the plug out of the RDC or remover the fuse, otherwise the car is still going to recognize the module and light is going to stay on.

Success! Did everything mentioned above but this time I removed fuse. No more tpms warnings, alerts in nav or instrument panel.

However, while coding the kombi it came up with a CEL out of the blue. It has been 3 days and its still there. I don't drive the car that much so I'm hoping it goes away on its own.

Originally Posted by lifo_1

Success! Did everything mentioned above but this time I removed fuse. No more tpms warnings, alerts in nav or instrument panel.

However, while coding the kombi it came up with a CEL out of the blue. It has been 3 days and its still there. I don't drive the car that much so I'm hoping it goes away on its own.

You can try this.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.

Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

Shawn you the man! CEL is gone. To recap for people wanting to disable TPMS

Pull the fuse in the trunk for TPMS.
Remove 2VB option in VO
HU_CIC / RDC = nicht_aktiv (this removes TPMS options from NAV)
KOMBI / ST_TYR_TIMEOUT = nicht_aktiv
KOMBI /ST_TYR_ALIVE = nicht_aktiv

Originally Posted by lifo_1

Shawn you the man! CEL is gone. To recap for people wanting to disable TPMS

Pull the fuse in the trunk for TPMS.
Remove 2VB option in VO
HU_CIC / RDC = nicht_aktiv (this removes TPMS options from NAV)
KOMBI / ST_TYR_TIMEOUT = nicht_aktiv
KOMBI /ST_TYR_ALIVE = nicht_aktiv

Glad I could help.

It went away the first time i drove it after clearing it but it came back after that. Comes back after i clear it everytime. Might have to take it in

Originally Posted by lifo_1

It went away the first time i drove it after clearing it but it came back after that. Comes back after i clear it everytime. Might have to take it in

CEL Zombie! Do you know what the CEL Code and its meaning is?

Maybe undo all your coding, clear it with Tool32, and see if it stays off. At least you will know if it is coding related.

hi guys, sorry to dig up this thread again but I could not manage to remove the RDC error message yet.

is it really necessary to remove the fuse to kill the error message? i dont even care about the yellow warning light much, i just want to remove the warning message from the idrive that pops up on every start.

I coded the 3 values as stated above, but I do not want to remove the fuse if not 100% necessary.
what does this mean: "Remove 2VB option in VO"? I have e-sys running and have coded a couple values before, but im not a coding expret. what is the VO?

update: well it wasnt too hard. I just had to remove the RDC fuse in the trunk. warning is gone forever thanks to everyone in this thread