Welcome to Bimmerfest -- The #1 Online Community for BMW related information! Please enjoy the discussion forums below and share your experiences with the 200,000 current, new and past BMW owners. The forums are broken out by car model and into other special interest sections such as BMW European Delivery and a special forum to voice your questions to the many BMW dealers on the site to assist our members!

Please follow the links below to help get you started!

Go Back   Bimmerfest - BMW Forums > The Best of Bimmerfest! > Do-It-Yourself H.Q.

Do-It-Yourself H.Q.
Share your DIY projects that have helped you keep your BMW running. For questions about how to fix your BMW use the model specific forums. All BMW DIY tips, tales, and projects discussed inside. Learn to work on your car and know the right BMW parts you will need!

Thread Tools Display Modes
Old 06-13-2015, 07:02 PM
dazz1 dazz1 is offline
Registered User
Location: New Zealand
Join Date: May 2015
Posts: 19
Mein Auto: 325i E90 2007
DIY Modify LEDs for superior map reading lights


This post describes the modification of LEDs to optimise their role as a light source for the map reading lights in the dome fittings on a BMW E90. It is a low cost and easy modification to complete. Just basic soldering skills are required.

Having recently purchased an E90, I decided to tweak it a little.
I purchased a set of LEDs to replace the interior incandescents.

The LEDs supplied were all OK but the T10 LEDs weren't really suitable for the map reading. The LEDs fitted but most of the light was going in the wrong direction.

I brought some T10 LEDs shown in the picture. Here the standard lamp and one of the unmodified LEDs are fitted into the bayonet holders. Note that the LED isn't tall enough to fit in the map light.

As supplied, they weren't really suitable for the map lights because they point the wrong way. That was OK because I brought these with the intention of modifying them.

The LEDs are fitted to a small board that is soldered to second board that fits in the lamp socket. I unsoldered the boards and rejoined them using strips of copper. The copper was 0.8mm by 2mm.

The strips were bent so the LED boards were tilted 35 degrees. This matches the angle of the dome fitting.

The T10 lamps are held in a bayonet type holder. The LEDs can only be fitted one way round.
On the rear dome light, positive needs to be forward. On the front dome light, positive needs to be at the rear. This means that left and right LEDs are required. The direction of tilt matters. I found out the hard way that the +/- symbols on the LED boards cannot be relied upon.

The result of the modifications were a set of four LEDs with a 35 degree tilt.

The next part is the installation.

The map reading lights have a clear plastic window that makes it impossible to remove the lamps from below.
Even if the windows weren't there, the lamps would be extremely difficult to remove.
The window and black surround cannot be removed from below. They are held in with plastic tabs.

The easiest and only way that I could replace the lamps was to remove dome light units.
The rear dome unit is removed by depressing the two spring clips on the rear edge with a trim tool.

The front dome light has similar springs along the front edge but these seem to be impossible to remove in the same way the rear dome tabs are depressed.

I pressed the front springs by removing the inboard sun shade brackets and pulling the roof liner down just enough to get my hand to the springs from above.

Here is what the LED looks like when it is fitted to the map light. You can also see a different type of T10 LED used in the central dome light. The modified LEDs now point in exactly the right angle to maximize useful light.

It is difficult to quantify just how bright the LEDs are.
I can look at the incandescent lamps but the LEDs are too bright to look at directly.
They are significantly brighter than the factory lamps.

The modified LEDs worked very well. The light is bright and directional. There is minimal light spill to annoy the driver.
I used the map lights on previous BMWs. I expect to use them on the E90. The LEDs are significantly better than the incandescent lamps.

Last edited by dazz1; 06-15-2015 at 03:18 AM.
Reply With Quote
Old 06-17-2015, 01:13 PM
slingshot22 slingshot22 is offline
Registered User
Location: Portland
Join Date: Jun 2015
Posts: 3
Mein Auto: E46 M3
Looks like an inexpensive way to get functional LED light in the cabin. Nice write up! Could you get a few pics of them on?
Reply With Quote
Old 06-17-2015, 05:49 PM
dazz1 dazz1 is offline
Registered User
Location: New Zealand
Join Date: May 2015
Posts: 19
Mein Auto: 325i E90 2007

I thought about that but it would be difficult to get a meaningful shot. A photo of the dome light(s) would merely show little light spill.
What is important is the lit beam pattern. That is not going to show illuminating black leather seats.

The colour of the map LEDs is a good white, so they are good to read with. The other LEDs have a distinctly cool blue tint which matches the black interior.

In the absence of good photos, this is a simple cheap mod that is easy to fit and easy to reverse if you don't like the LEDs.
Reply With Quote
Old 02-14-2017, 06:32 AM
Debille Debille is offline
Registered User
Location: Denmark
Join Date: Sep 2013
Posts: 14
Mein Auto: BMW 520D 2011
It is actually very easy to remove the front light as well. I have a BMW 730 D - F01 - 2010 model. Just take of the black frame, and look into the to round holes. In there you find two small screws, that you just loosen. Use a 2 mm Unbraco key (Allen Bradley hexagon). Be carefull when you take out the small screws, theř are very "lively" C", When the screws are removed, just take the console down in the front. Replace ligth balls, and put it all together again. Takes 10 - 15 minutes.
Attached Thumbnails
Click image for larger version

Name:	IMG_4770.JPG
Views:	43
Size:	37.3 KB
ID:	589335   Click image for larger version

Name:	IMG_4769.JPG
Views:	44
Size:	24.0 KB
ID:	589336   Click image for larger version

Name:	IMG_4768.JPG
Views:	48
Size:	37.0 KB
ID:	589337   Click image for larger version

Name:	IMG_4774.JPG
Views:	49
Size:	33.2 KB
ID:	589338  

Last edited by Debille; 02-14-2017 at 06:43 AM.
Reply With Quote

See More Related BMW Stories

Forum Navigation
Go Back   Bimmerfest - BMW Forums > The Best of Bimmerfest! > Do-It-Yourself H.Q.
Today's Posts Search
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -7. The time now is 10:27 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
© 2001-2015 performanceIX, Inc. All Rights Reserved .: guidelines .:. privacy .:. terms