Welcome to Bimmerfest -- The #1 Online Community for BMW related information! Please enjoy the discussion forums below and share your experiences with the 200,000 current, new and past BMW owners. The forums are broken out by car model and into other special interest sections such as BMW European Delivery and a special forum to voice your questions to the many BMW dealers on the site to assist our members!

Please follow the links below to help get you started!

Go Back   Bimmerfest - BMW Forums > BMW Model Discussions > 5 Series > 5 Series DIY

5 Series DIY
Knowledge Is Power! ~ The place for do-it-yourself threads on a variety of topics. Start a thread describing a particular job (oil change, cooling system overhaul, brakes, shocks and springs, etc.) or search for one you need help with!

Reply
 
Thread Tools Display Modes
  #1  
Old 09-14-2010, 07:42 PM
bgal530 bgal530 is offline
Registered User
Location: Fairfax, VA
 
Join Date: Sep 2010
Posts: 4
Mein Auto: 2003 530i
DIY- Replacement of Leaky Power Steering Hoses

E39 Power Steering Reservoir Hose Replacement


I'm not sure how to get the photos to stick in this thread, so please look at the attached link


As I was switching over to my summer tires, I noticed some shiny liquid stuff on the lower engine cover. A 5 minute investigation and a quick trip to the internet revealed a very common problem Ė leaking power steering hoses at the reservoir. Many people simply cut off an inch of hose and attach new hose clamps, which will work just fine, but if you decide to commit, these steps and photos hopefully make it easier:


Work took place on a 2003 530i w/manual transmission, build date of 9/02 at 75k miles. My tell-tale sign was the power steering fluid covering the lower engine cover. Yours may be low level in the reservoir, or a pink fluid on the floor of your garage. Run your fingers underneath the p/s reservoir. If they come out grimy w/power steering fluid, itís time to get out the wrenches.


Required Consumables (from RealOEM.com):
1. 32411095526 Intake Manifold (Hose to P/S Pump)
2. 32411094306 Radiator Return Line (Hose to Cooling Coil)
3. 17211742636 O-ring for installation to cooling coil (2 required)
4. (2) 6 Ė 20 mm hose clamps for Intake Manifold Hose
5. (1) 9 Ė 24 mm hose clamp for Radiator Return Line
6. Lots of rags to mop up power steering fluid
7. Power Steering Fluid Ė for sedan, use a high-quality ATF per the Bentley Manual. I used Mobil-1 Synthetic ATF. The Tourings, I believe, use Pentosin- DONíT MIX THE PENTOSIN FLUID W/ATF. Nothing good comes of that chemistry experiment.


Accessing the hoses: The first order of business is removing the air filter box.
Keep this picture in mind to remember how the hoses are routed, etc. when you finish.


Itís less painful to remove the Air Filter Box, the Mass Airflow Sensor, and the hose between the MAF and the Throttle Body as one unit. Loosen up the hose clamps around the Ďhoseí (near the throttle body, not the MAF) and down near the driverís side headlight, remove the bolt that holds the assembly to the fender, and pull out the vacuum hose plugged into the top of the Ďhoseí. I broke this plug during my cooling system overhaul, and it set me back all of three dollars (at the dealer, no less). Finally, a cheap part!


Now that the air filter box, MAF, etc. are out of the way, you have plenty of room to work. In this picture, you donít see a lint-free rag in the engine intake to the throttle body, but itís because my bright yellow rags donít photograph well.


Now is a good time to remove the lower engine cover (if you havenít already, and get prepared to drain the system through the power steering hose at the base of the p/s pump.


To drain: Looking at the picture, you can see the annoying clamps that come from the factory. Get a good pair of straight cutters and hack this off. Get your oil drain pan ready, and pull the hose off, trying not to get doused in p/s fluid.


Go ahead and open the cap on the p/s reservoir now so the fluid will flow freely into your drain pan. Once this step is complete and you wipe up the mess, youíre done under the car for a while.


Removal of hoses and power steering reservoir: The next thing I did was remove the power steering hose from the cooling loop. This system is a bit on the fragile side, so use caution. I think I used a 4Ē extension to get at the bolt in between the two p/s cooling lines. The bolt, the hoses, and the block holding everything in place come out together, so just give the hoses a gentle tug and donít worry about breaking anything. Throw out the crush washers on the ends of these hoses. Youíll be replacing the lower hose, so free him up so you can pull it out with the p/s reservoir.


Now youíre at a point where you can remove the power steering reservoir. The power steering reservoir removal is very straightforward. Just remove a few bolts and pull it off the engine. You can now use your straight cutters to remove those factory hose clamps from the hoses, throw the old hoses in the trash, and clean up all the p/s steering fluid off of the reservoir.


Thereís a filter inside the p/s reservoir, and Iíve heard of some people turning the reservoir upside-down and back-flushing p/s fluid through the filter. Iím not that hard-core, but it shouldnít harm anything.


Putting it back together: The first thing I did was slide my new hose clamps over my new hoses and attached the hoses to the now-clean reservoir. Reinstall the reservoir onto the engine. With the hoses unclamped, wiggle them around until theyíre correctly located to meet up with the power steering pump and the cooling coil.


At the cooling coil, INSTALL NEW CRUSH WASHERS, place the two hoses in the retainer block, and tighten the retainer with the one bolt in between the hoses. This assembly is somewhat fragile and I couldnít find a torque spec, so I went with something more than snug, but less than gorilla. Months later I have no leaks, so I guess itís OK.


Thereís a double-ended clip that attaches to the hose you just installed and the heater hose. Nowís as good a time as any to put that back on.


The power steering pump hose is very simple. Slide the hose clamp on, attach the hose to the power steering pump, and tighten the clamp. At this point, you can go back up to the p/s reservoir, make sure there is no strain on your new hoses, and tighten the two hose clamps.


Almost Miller Time- take a look at your hose routing and double check that everything is tight. Itís easier to do rework now than when the air filter assembly is reinstalled. I used Griotís engine cleaner to clean up the remaining p/s fluid, but there are other great cleaners out there.


Once youíre sure everything is looking good, itís time to reinstall the air filter/MAF. Remove your lint-free rag from your now-open intake, put the assembly back on, tighten your two hose clamps, install the bolt, and reattach the vacuum hose fitting.


Filling the system: SLOWLY fill the system with a high quality ATF. Swing the steering wheel right and left. Top off again. Start the car, slowly move the steering wheel from lock-to-lock. Check the fluid and top off. Look for leaks. If everything is looking good, reinstall the lower engine cover, ensure the p/s cap is tight, and then on to the best part (besides the post-maintenance cocktail):

Road test:

Last edited by bgal530; 09-14-2010 at 08:02 PM. Reason: Corrected broken link
Reply With Quote
Ads by Google
Reply

Bookmarks

Tags
power steering


Forum Navigation
Go Back   Bimmerfest - BMW Forums > BMW Model Discussions > 5 Series > 5 Series DIY
Today's Posts Search
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



Forum Jump


All times are GMT -7. The time now is 04:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
© 2001-2011 performanceIX, Inc. All Rights Reserved .: guidelines .:. privacy .:. terms