Bimmerfest - BMW Forums

Bimmerfest - BMW Forums (https://www.bimmerfest.com/forums/index.php)
-   E63 / E64 6 Series (2004 - 2010) (https://www.bimmerfest.com/forums/forumdisplay.php?f=114)
-   -   delete (https://www.bimmerfest.com/forums/showthread.php?t=1154289)

derekwilkinson 11-15-2017 11:35 AM

delete
 
problem fixed

HerbP 11-16-2017 10:04 AM

Something is loading down the engine while the AC is on. As always 1st check the battery & alternator voltage. Next I would start looking for a vacuum leak somewhere in the CCV system. This could be a cracked vent pipe, or a bad diaphragm on the CCV valves. I would also check to make sure the oil cap & dipstick are both firmly seated.

derekwilkinson 11-16-2017 10:06 AM

delete

derekwilkinson 11-16-2017 10:29 AM

delete

///Bruce 11-17-2017 06:07 PM

Any noise from the belt? As if the compressor is starting to bind up?

derekwilkinson 11-17-2017 07:09 PM

delete

HerbP 11-17-2017 07:12 PM

Quote:

Originally Posted by derekwilkinson (Post 11547249)
thanks. will check voltages and oil cap/dipstick.

how do i check the CCV system for leaks?

https://www.bimmerfest.com/forums/sho...d.php?t=618923

does that apply to the 650i as well?

Yes that would apply to the 650 as well. If you carefully pop the caps off, you can inspect the diaphragms for damage. They are easy to remove & inspect. I would also inspect the CCV vent tubes for cracks. Be careful moving them around. If they are old they can crack easily, & cost around 85.00 each.

derekwilkinson 11-17-2017 07:14 PM

delete

HerbP 11-17-2017 08:00 PM

Hopefully you will find your problem. also make sure that the cold air tube to the intake is fully seated, & not sucking in un-metered air.

derekwilkinson 11-17-2017 09:28 PM

delete

derekwilkinson 11-20-2017 05:37 PM

delete

HerbP 11-20-2017 05:59 PM

Did you check the voltage to make sure the battery is ok? Have you used INPA to see if any cylinder is running rougher than any other? It is a little early for spark plugs, but it can't hurt to see what the plugs look like.

derekwilkinson 11-20-2017 06:04 PM

delete

HerbP 11-20-2017 06:10 PM

If you go into INPA & connect the car, run the analog values on the engine. It will show you a graph on each sensor, & cylinder. Look at the post by Tripleblack, he has some INPA graphs in his post. If INPA acts funny, keep pressing the keys to you get your values. I do not know why ISTA did not incorporate this into its program, or I do not know how to get to it?

derekwilkinson 11-20-2017 06:11 PM

delete

derekwilkinson 11-21-2017 10:47 PM

delete

derekwilkinson 11-21-2017 10:48 PM

delete

HerbP 11-22-2017 07:15 PM

I would try reloading INPA, & install in English UK I think. Sometimes crossing different versions can cause this also.


All times are GMT -7. The time now is 06:00 PM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
© 2001- VerticalScope Inc. All rights reserved.