BimmerFest BMW Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 48 Results
  1. E39 (1997 - 2003)
    So, I've joined here to ask for some help with my 2000 540i6. I'm getting a P1519 code that keeps going on and off about every 2 starts in succession. A bit of research indicates that the P1519 code is for a stuck vanos solenoid. -- P1519 Camshaft Position Actuator Bank 1 -- The car has 190k...
  2. E39 (1997 - 2003)
    so i bought a 2000 BMW 528i about 2 weeks ago. the car had sat for a long time before i picked it up, so it had plenty of issues. I did a decent amount of work on the coolant system to fix some leeks prior to jumping into other stuff. at that point with the leaks it ran and drove great. After...
  3. Parting Out
    These came out of my 330 with 189,000 miles. Not pitting or such. They look smooth with no issues. Both cam's for $100 plus shipping. I can take more pics or video if needed just let me know.
    $100 USD
  4. E60 / E61 (2004 - 2010)
    2A7A - Camshaft position control, deactivation. I believe one of the valves were open during a walnut blast and some got in there. Friend believes some might be in the oil pump causing my issues. When I turn it on it idles great for 20 seconds before the half engine shows and this code (along...
  5. E60 / E61 (2004 - 2010)
    I've got a 2005 525i with the older 2.5L M54 engine. I've been having the P0011 or 28B6 error intermittently for the past couple of years. I have noticed that when the error is gone (service engine soon light is off on the gauge cluster) it typically comes back on startup when its a bit colder...
  6. 7 Series - E38 (1995 - 2001)
    So my 2001 740iL acquired a cylinder 5 misfire and fuel cut off over night. When I ran the code scanner, one other code popped up. Not only was I getting the misfire code, I also got a “Camshaft Position Sensor A Circuit High Bank 1 or Single Sensor” (Code P0343). I didn’t know if this code...
  7. E60 / E61 (2004 - 2010)
    2009 BMW 535i Not a mechanic and I don't DIY either. I just no basics like oil and tire changes Initial Problem: Had an oil change done and found major leak. Oil Leak which has yet to be fixed. Have been driving vehicle but have been putting quarts of oil in ever few days or once a week or so...
  8. F10 / F11 (2011 - 2016)
    BMW 2012 528i xDrive N20 F10 82Kmiles Replaced both CPS, cleared error code. Run the car a few mins then the P1339 error code pops up again. Here's another weird happening, the serpentine belt makes noise when at low rpm when the error code is on, but when I cleared the error serpentine belt...
  9. E90/E91/E92/E93 (2006 - 2013)
    I had issues with my 335i not starting but cranking and turing off in the middle of driving and wont turn back on but did crank. I checked the codes and end up replacing the crank shaft positioin sensor, replaced intake camshaft position sensor and had to replace the battery that was main...
  10. 7 Series - E65 / E66 (2002 - 2008)
    Good evening, I just recently replaced the valve stem seals on a 2007 BMW 750i with a 4.8L N62B48B engine. I went to start it up and the engine runs rough then stalls. This problem never existed prior to the job. I did disconnect the and remove the intake manifold during the process, upon...
  11. E90/E91/E92/E93 (2006 - 2013)
    Hi All, I've got an '09 328i (158k) that I'm trying to hang on to but it looks like an uphill battle. Let me know if you have some thoughts on this. Lately the fuel economy has been appalling (15 MPG), and the valve gasket has been leaking. I took her in for just a new valve cover as I'd have...
  12. E46 (1999 - 2006)
    Designed to properly align and lock the camshaft. Comes with timing chain pre-tensioning tool, tuning wrench, camshaft timing setting tool, tensioner locking tool, and I'll include the hex key along. 35$ - for 1 week 30$ - for 1 week if you're military (show I.D proof) :) 60$ - Deposit, Ill...
  13. Parting Out
    I have a couple of spare VANOS gears from my 2000 540i. I picked up a couple of used gears before I did my timing guides and had them rebuilt so everything was ready to go when I started the job. $125.00+$13.00 for shipping. They need to be rebuilt. Do it yourself for dirt cheap or I used the...
  14. X5 E53 (1999 - 2006)
    Hello, After a few months of work, I finally was able to correctly time the M62Tu engine and now only have one code (that is new): 71 Signal, Camshaft position sensor, bank 1 (passenger side) The X5 also has a throaty sound coming from the engine, that didn't happen before and sprays oil...
  15. E90/E91/E92/E93 (2006 - 2013)
    My 2007 335xi is throwing code P0015 and is making a horrible noise I will leave a link to a video I posted on YouTube of the car as you will see in the video the noise comes and goes if you have any idea of what it is PLEASE HELP!!! Thank You in advance...
  16. E39 (1997 - 2003)
    Hey guys - I've been back and forth through old posts trying to diagnose a camshaft CEL I'm getting. I'm always a searcher prior to posting for help, I just have not been able to find the next item to check, any help would be greatly appreciated. Picked up a 2000 540i, and pulled the following...
  17. E39 (1997 - 2003)
    Hello everyone. I'm kind of at the end of my rope here so I'm hoping I find some answers. Thank you for reading. The issue at hand is my 2000 MF2TU 528i. I'm getting a "Control VANOS, position, exhaust camshaft (OBDII: P1523)" code and engine light on. The symptoms are the usual: -Complete...
  18. E60 / E61 (2004 - 2010)
    Hello guys, i have a 530i e60 2006 I've been going through a certain problem, im going to start from the beginning.. Service engine showed up and scan showed vanos intake and exhaust solenoids malfunctions, i cleaned them a bit and put them back, after a while the fault showed again. I replaced...
1-19 of 48 Results
Top