BimmerFest BMW Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-16 of 16 Results
  1. X1 E84 (2011 - 2015)
    Hi everyone, 2012 e84 28i xDrive So, I have the following lights on my instrument cluster and iDrive: yellow ABS and DSC (car with zigzag road?), red hand break and red car on hoist. iDrive says Electrical System Malfunction. Car drives perfectly fine. I believe the code that's causing them is...
  2. F10 / F11 (2011 - 2016)
    Hello everyone, I expose you today a problem that I have with my BMW F10 528i of 2010, an engine N53B30. I did a lot of research in French, English and German but I did not manage to find an answer. As far as the car behavior is concerned, when it is cold, it starts without any problem with a...
  3. BMW Coding and Programming
    Hi everyone, Does anyone have the can bus ID information pertaining to rpm & parking brake lights on the F10/15/20 series. I believe they are the same for the ones I have mentioned. I'm trying to setup a cluster bench test setup and can't seem to figure out these two. Any help would be highly...
  4. E39 (1997 - 2003)
    Okay so my car is '01 525i, Automatic, sedan, M54B25. I love this car, bought it 4 years ago from an owner who neglected it for years. I've mended it and it runs heavenly now. There are no big issues with this car in the last couple of years that would leave me stranded on the side of the road...
  5. 7 Series - E38 (1995 - 2001)
    The ECU temperature sensor, is that normally open or normally closed with regards to its resistance? I believe my temp sensor is bad. Reads 0.0 Ohms so it is closed. Regardless if it’s in near boiling water or sitting on a block of ice it’s reads closed. The reason I think the ECU temperature...
  6. General BMW Questions
    The ECU temperature sensor, is that normally open or normally closed with regards to its resistance? I believe my temp sensor is bad. Reads 0.0 Ohms so it is closed. Regardless if it’s in near boiling water or sitting on a block of ice it’s reads closed. The reason I think the ECU temperature...
  7. E60 / E61 (2004 - 2010)
    Hi! Since i buy the car, i have a problem with can modules, but today the car went to limp mode, so i want to figure it out what's wrong. CAR: 2003 BMW e60 530i - M54B30 My error codes after limp mode: 28DD - DME: Air mass system - Existent 28AE - DME: Torque limitation: Monitoring - Existent...
  8. E60 / E61 (2004 - 2010)
    Hello All, I am trying to fix some electrical issues at this point and do not know what to do. My sunroof has no power going into it. The fuse is fine. No power going to the rearview mirror for the auto dark feature. I have no alarms. On ISTA these modules are in red meaning no communication or...
  9. General BMW Questions
    On my E61 I recently installed this Android box that intercepts the LVDS cable between the CIC unit and the display and lets me do wireless CarPlay or stock CIC by switching with the idrive knob. It came with a wire harness that lets me tap the CAN wires either from the CIC or from the idrive...
  10. BMW Coding and Programming
    I'm fiddling with an Arduino with a can bus shield to get data from the can bus of my X3 F25 30d -2011 I connect to the K-can 2 bus (wire splicing) and have found a lot of info like engine rpm, throttle position, fuel tank level, lock status for the doors and some more good stuff. What I...
  11. E39 (1997 - 2003)
    Hi guys, thought I'd post a link to this very informative video that explains how to diagnose an e39 transmission fault that highlighted a CAN bus issue, and shows that the problem ultimately lay within the ABS module... https://www.youtube.com/watch?v=uKnQI2IScPU Note, I do not have such an...
  12. BMW Coding and Programming
    Hi, I have a BMW m235i f22 (2014), and i want to control door locks, lights remotely with my computer. I am trying to access the OBD2 port using my Arduino/Spark-fun shield to read the CAN messages, but the only CAN ID i see is 0x130. The CAN ID doesn't change before or after ignition or drive...
  13. E90/E91/E92/E93 (2006 - 2013)
    Hello folks, Looking for some advice here... I have a 2006 E90 with a few error codes that are showing. CEL came on, I pulled the codes and found 9 separate codes. I am looking for help on the CAN bus related errors. The footwell module (FRM) shows 3 error codes, two relate to the active...
  14. BMW Coding and Programming
    I am trying to monitor the can bus messages on my f series 2015 435xi. I have purchased the K+D Can Bus USB cord (the green one, not the fake white one). Is there any software application which I can use to monitor the messages that are being sent across the bus or does no such software exist...
  15. E39 (1997 - 2003)
    ANY and ALL help or advice is greatly accepted.. I have a 98 528i (7/98) build date. The asc light is constantly on and will not go off. Also, there is a significant loss of power and "rougher" shifting points. Tranny is NOT in limp mode, but will not downshift, but will however shift down 2...
1-16 of 16 Results
Top