BimmerFest BMW Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 103 Results
  1. BMW Coding and Programming
    Hi all, I have had the joy of experiencing coding on a BMW and my first project was replacing a NBT EVO on a G30 with one bought on eBay. The original one was stolen and the replacement head unit had the same options as my vehicle (checked through www.realoem.com). My original FSC codes...
  2. BMW Coding and Programming
    Hey guys ! Installed a single stage wheel airbag (europe spec). Does anyone have an idea on how to code it ? I coded a single stage airbag on an F30 and an F10 before and I had to change these in the ASCM module: ACSM Module 3000 Function-airbag_fahrer_stufe_2-> set to nicht aktiv...
  3. 1 Series & 2 Series
    Heyy guys, I got an issue with the air bag i change the module for maybe 6 times ,then i was thinking maybe thr issue with the salapa element. So anyone can help me and post the m2 f87 2017 salapa element. Because I'm already try to take it out from bimmer.work but it's won't work i don't know...
  4. BMW Coding and Programming
    Hi guys my esys launcher won’t load I get an error on start up. Esys 3.33 loads and works ok.
  5. X5 F15 (2014 - 2018)
    Hello everyone, first post here! I have a 2015 BMW X5 xDrive35i xLine and im looking for someone to help me code in sport+ mode. I’ve looked at other forums and post and most of the coders that were able to help haven’t been online in years. Hopefully someone else can help me. Thank you!
  6. BMW Coding and Programming
    Hello Are there any esys experts who can help me coding the car to a manual transmission. I wanted to swap the transmisson to a manual but i dont know how to code it.
  7. 7 Series - F01 / F02 / F03 / F04 (2008 - 2015)
    Hello guys , I got on issue with the active steering to cancel it from the dashboard . I tried in the Dkombi and also in the ASA but nothing in the FDl edit is there. Can anyone help me with that ? Thank you
  8. F10 / F11 (2011 - 2016)
    Hi , I tried somany codes to active my bmw 528i f10 2015 easy entry&Exit by Esys , But didnt successful , Who can Guide me ?
  9. F10 / F11 (2011 - 2016)
    Hey all, This is my first post and would appreaciate some help with this. I have a 2012 F10 which has an RPA failure message in Vehicle Information in iDrive. I scanned it using Launch and found a code in DSC: "4806D5 - Run Flat Indicator: Initialization Implausible". And the Reset Tyre...
  10. General BMW Questions
    Hello guys, As per the below picture i try to remove the right corner malfunction from the dash board theought the esys in the BDC . I try the WARM and KALT fekm aicht to nicht but nothing is useful.
  11. General BMW Questions
    Attention all Forum users. I'm announcing a FREE promotion. If you have the equipment to work with your car (like a kdcan, Enet, Icom, VCX) I offer free assistance in diagnosing and coding your car. Just write to me and I will try to help you by remotely connecting to your computer, make the...
  12. F30 / F31 / F32 / F33 / F34 / F36 (2012 - current)
    Hi guys, I have bought a coding cable from Aliexpress for my F30 3.20D and the seller didn't send the download link for ESYS 3.22.5 software. Is there anybody who has a link to download? If yes, could you please share it with me?
  13. BMW Coding and Programming
    Hi friends, I'm a bit new to this forum and would like some help with my new ICM that I bought to replace the first broken ICM. While flashing this new ICM using Esys 3.30 I had an error with a bad bootloader and unknown software ... can someone with expertise help me using teamviwer ... thank...
  14. F30 / F31 / F32 / F33 / F34 / F36 (2012 - current)
    Hello. Yesterday I tried to flash a 2014 428i N20 with bootmod3. Everything went okey except for DME Encoding at the end. After this the car wouldn’t start and I wasn’t able to restore it. Ecu doesn’t not respond in ISTA and in ESYS it’s missing it’s CAFD file. i have tried to update the dme to...
  15. BMW Coding and Programming
    Can anyone point me towards the place in esys where I can change the colours in my ambient light menu. From what I've read, I need to replace one of the slots already there. E.g. I want to replace the white colour with red. Has anyone done this and can help? Also wanting to engage door handle...
  16. BMW Coding and Programming
    Hello, Maybe someone can help me. I have an error after start the Tal processing. It ends with the message „abortedbyerror“. I think the error is the „programming counter exhausted“. is it possible to deactivate the programming counter check in esys? Or another solution? Read SVT before TAL...
  17. BMW Coding and Programming
    I have a 2015 i3 that has the 3G TCB, and as we all know, 3G goes away in Feb of next year. I enjoy the remote services for checking the charge level, or pre-heating in the winter. I have obtained a TCB from a 2017 i3, and it was never registered with connected services for the vehicle Vin. My...
  18. G20 (2019 - Current)
    Hi all, I want to install a 3AG OEM backup camera on my BMW M4 Comp 2021 (G82). When I bought the car I was ordered to equip with PDC, but not with backup camera, and now I would like to have this feature... My BMW Dealership tolds me that from BMW side could not activate the module, however...
  19. X5 F15 (2014 - 2018)
    Hello colleagues , I received the following error when tried to inject CAFD for EPS on BMW F15 2016. I tried with Esys 3.33.4 with different full PSdZData (v4.28.41, v4.30.41, v4.32.12). Have ideas what is the issue?
  20. BMW Coding and Programming
    Hello everyone, First of all, I want to apologize for my bad english! I recently did some coding with Bimmercode and e-sys with the yellow cable and installed a front and rear camera module on a 5 Series (2016) F11 with NTB 6.5' + 6WA pannel. During the installation of the cameras, I had to...
1-20 of 103 Results
Top