hi guys, when trying to open Tool32 i get the following error:
Failure in apiInit()
abort the program!
The expertmode profile is always named "default" once you install the INPA and NCS Expert. In order to code and program any bmw feature, you need to setup the so called "expertmode" profile so in this video I will show you how to set it up. In the video I revealed the password which is: REPXET I...
I purchased an enet cable online that works with icom and ista. The diagnostic part of ista works. I change the registry from programming with ista false to true. I currently have chasis malfunction and need to program parking brade module and fuel pump cobtrol unit. Also i need to calibrate...
Hi. I have a g30 in today with a suspected faulty BDC Module. I have tried to use ISTA D on it but it throws an error message. “The Programming system could not be initialized. The ISTA installation may be damaged or incorrectly configured”
I have no problem with F series vehicles but then again...
I am having a hard time updating iDrive on my 2016 X4. I've even talked to customer relations and we were both stunped so would appreciate any insight anyone has..I downloaded the software to my empty FAT32 formatted UDB drive, plugged it into the car, started it, and navigated to the...
I'm unable to get over the air software upgrades on my X7. This has been going on for over 5 months and has been passed from BMW Genius to BMW Assist to BMW Customer Services. None of them can resolve the issue except to get the dealership to manually push the software onto the vehicle. After...
Help please! Had a replacement battery a few weeks ago (flat battery). 2 weeks later the battery was flat again. Garage can't indentify any problems (alternator ok, and says there is no constant drain). They said they said that they found a technical bulleting that said the media system can...
Hi All, this is my first post, I searched everywhere on how to get latest software for my 2008 e70 with no luck..
I have a transmission issue (clunk sound on startup) that should be fixed by updating the software.
Can anyone please tell me where should I start, send me a link or advise?
Many thx :)
Hi I've just purchased a led headlight for my f21 lci Bmw I've been told I need to program this. Can anyone guide me on what software I will need and what I will need to do.
I'm decent with computers if that helps with explaining.
Any help will be appreciated ☺️
i bought a E61 as a Daily, now i would retrofit the Media Combox, for this i have firstly to do the Software/Frimware Update of the CIC.
i did this for my F10 with E-SYS but i don't know how it's to do for the E-Series BMW's.
can anyone help me?
Bought January 2019 with 238k miles. First BMW. After a couple of months, unless I "nursed" the accelerator, the car would misfire, then there would be a constant SES light and the computer seemed to shut off the offending coil pack(s) until the car was shut down and re-started. After that the...
One disappointing feature about my 2016 740i is that software updates are very few and far between. Tesla on the other hand is constantly upgrading their software and are quick to send these out to all their cars.
Sounds like BMW is penny pinching, especially since they now charge a yearly...
I have coded with Carly app with success but now I need something more...
I have finished installing Ista-D which is working, for instance I have read battery history which on Ista-D has a lot more information than Carly could show.
I am going to install INPA F, NCS Expert, WinkFp, Tool32, NCS...
I recently purchased a 2008 X3 (automatic transmission, great condition, only 58,000 miles). I notice when driving, the car sometimes shifts hard from 1st to 2nd gear, and also 2nd back down to 1st. I have read through some threads on this forum, and I'm wondering if my transmission ever...
I have BMW 5 series 2010 witch cic I-drive and navigation system. The car is September 2010 I have 2 questions.
Q1 - I am not able to update the firmware/software as there is no software update tab in my menu.
Q2 - Is there any way that I can update my CIC to NBT and who can do...
Hope some one can help e with this.
I'be been trying for a long time to find a software that can connect correctly with my 2010 E91.
I've tried INPA, but it doesn't work. Got a message saying:
"Requested Control Unit: D71N47A0 not found.
Control unit found: D70N47B0.
Program will be...