Did you search KOMBI for RDC setting, and if that did not work, remove 2VB from VO and VO Code KOMBI, HU_CIC, and RDC?

 

Ta da!

Kommentar=RDC Ueberwachung (Comment=RDC monitoring)

KOMBI / ST_TYR_TIMEOUT = nicht_aktiv
KOMBI /ST_TYR_ALIVE = nicht_aktiv

 

I tried those 2 above and it didn't fix. I will try to remove 2VB from vo

 

Hmmm...that surprises me that those two did not kill it.

Ok. Try this one too:

KL_PREDRIVE_F10_RPA = nicht_aktiv

If unsuccessful, kill 2VB in your VO, and VO Code HU_CIC and KOMBI. RDC has no coding data, so there is nothing to VO Code there I don't think.

 

Removed the 2VB and VO coded HU_CIC and KOMBI.

No luck. TPMS warning still present in NAV screen and instrument panel

 

That is almost impossible to believe. Are you sure after you removed 2VB from FA, that before you VO Coded HU_CIC and KOMBI, you loaded that FA (the modified one without 2VB) and activated it, and not the FA read from the car?

 

So load the xml file with the 2VB option removed and VO code those 2 again?

 

Yes! That is why removed it. Now when you VO Code the ECU's, it won't enable 2VB like your regular FA that is stored in your car will (assuming you did not go so far as to write the modified FA to the car, and the FA in the car is original).

 

Just to keep the thread alive I have confirmed with Sean what I did was correct. New FA and VO coded Kombi and HUCIC. Still not luck. Will keep researching

 

when you remove the 2VB out of the VO, you still need to pulll the plug out of the RDC or remover the fuse, otherwise the car is still going to recognize the module and light is going to stay on.

 

Success! Did everything mentioned above but this time I removed fuse. No more tpms warnings, alerts in nav or instrument panel.

However, while coding the kombi it came up with a CEL out of the blue. It has been 3 days and its still there. I don't drive the car that much so I'm hoping it goes away on its own.

 

You can try this.

Assuming the fault condition no longer exists, to clear the fault code.

1) Launch C:\EDIABAS\Bin\TOOL32.EXE
2) Hit F3
3) Load C:\EDIABAS\Ecu\F01.PRG
4) In the "Select Job: F01" window, select FS_LOESCHEN_FUNKTIONAL
5) Hit F5
6) "Results" window should show "JOB_STATUS = OKAY"

Hopefully, Problem Solved.

Note: fs_lesen_funktional only read fault codes, FS_LOESCHEN_FUNKTIONAL will delete it.

 

Shawn you the man! CEL is gone. To recap for people wanting to disable TPMS

Pull the fuse in the trunk for TPMS.
Remove 2VB option in VO
HU_CIC / RDC = nicht_aktiv (this removes TPMS options from NAV)
KOMBI / ST_TYR_TIMEOUT = nicht_aktiv
KOMBI /ST_TYR_ALIVE = nicht_aktiv

 

Glad I could help. :thumbup:

 

It went away the first time i drove it after clearing it but it came back after that. Comes back after i clear it everytime. Might have to take it in

 

CEL Zombie! Do you know what the CEL Code and its meaning is?

Maybe undo all your coding, clear it with Tool32, and see if it stays off. At least you will know if it is coding related.

 

hi guys, sorry to dig up this thread again but I could not manage to remove the RDC error message yet.

is it really necessary to remove the fuse to kill the error message? i dont even care about the yellow warning light much, i just want to remove the warning message from the idrive that pops up on every start.

I coded the 3 values as stated above, but I do not want to remove the fuse if not 100% necessary.
what does this mean: "Remove 2VB option in VO"? I have e-sys running and have coded a couple values before, but im not a coding expret. what is the VO?

 

update: well it wasnt too hard. I just had to remove the RDC fuse in the trunk. warning is gone forever thanks to everyone in this thread

 

Just wanted to know how you found what fuse it was. I have a 2015 f30 and have tried everything you did. I remove a fuse that has the tire symbol with exclamation. On mine its 132. Coded all that was mentioned and I still get all the warnings. I tried looking for the RDC module to unplug but no luck. I looked in all locations mentioned online. IM guessing it changed for 2015.

I did it on my 2013 f10 removed fuse coded and all worked with no lights or messages. I didnt have to remove 2VB from VO for that one.

 

Sorry for bringing back an old thread but I am trying to get my TPMS disabled since I have after market wheels. I am really confused about VO and what it is or where to find it. The same goes for the location of the RDC fuse in the trunk. I have some coding experience and have everything needed to code, just don't know where it is within the program. Thanks in advance.

 

Sorry for bringing back an old thread but I a trying to get my TPMS disabled since I have after market wheels.

Reading through this thread, it seems to be more trouble than it's worth to me. Just pick up a set of the damn TPMS sensors on eBay for about a hundred bucks and be done with it!

 

Got it working on my F01. I did everything previously mentioned in this thread minus the 2VB and VO thing. You may want to skip it and see if you are good as well.

 

I'm not Shawn, but yes, same process will clear the code providing it's not an ongoing issue.

 

:thumbup:

 

I tried doing it on my f10 but I didn't do the HU_CIC / RDC = nicht_aktiv because I have the hu nbt don't know if it will mess with other things. I did do the KOMBI / ST_TYR_TIMEOUT to nicht_aktiv all that did is reset my time and date. The KOMBI /ST_TYR_ALIVE = was already set to nicht_aktiv. I also pulled the fuse and Im still getting all the warnings... weird...

 

I did notice a difference just by the one setting I changed. Now it does not warn me as soon as I start car. It takes about a minute before all the lights start flashing.
It makes me wonder if that setting I changed to not active is the time it takes for it to warn. maybe if I change the value? what do you guys think? Just a thought.

 

Thanks fellas, I am good to go now.

 

So CEL came back shortly after reset. I changed the coding for KOMBI back along with putting the fuse back in. I did another reset and was good. At this point, I'll deal with the tpms light....seeing the CEL throws me off and makes me think something's wrong.

 

All is good no lights on dash.... I did what post #3 says

 

Were you able to remove Cell?

 

hello, Shawn
advice on TPM / RPA E66 screen shows system error
Can not initialize

Thank

 

Sorry, but I do not know the cause of the Initialization Error. Maybe you have a bad sensor or TPMS Module. Have you tried Coding it with NCS Expert?

 

RPA in side CIM module. read fault by ista - no fault in store
but read by inpa - fault in CIM =D998- All groups

 

Nope. Could you please share how to get it? Thanks again!

Sent from my ONE A2005 using Tapatalk

 

Nope. Could you please share how to get it? Thanks again!

Sent from my ONE A2005 using Tapatalk

PM sent.

 

Tool32 seems to hang when I load f01.prg. Am I missing a step? Thank you...

Sent from my ONE A2005 using Tapatalk

 

Tool32 seems to hang when I load f01.prg. Am I missing a step? Thank you...

Sent from my ONE A2005 using Tapatalk

Disable Windows Firewall, and run Tool32 with Admin Rights.

 

Shawn you rock. Thanks much!

Sent from my ONE A2005 using Tapatalk

 

Shawn you rock. Thanks much!

Sent from my ONE A2005 using Tapatalk

:thumbup: