I understand now lol. Thanks

 

Shawn do you know why this module is missing the CAFD file? How do I put it back in?

 

Shawn do you know why this module is missing the CAFD file? How do I put it back in?

Gee, DME is missing CAFD, Imagine that.

I told you long ago, at the beginning, in Post #20 and #22, that your problem was most likely caused by missing or corrupt DME CAFD, and if that was the case, you needed to Inject CAFD into DME and VO Code it.

And now here we are, in Post #84, you confirm that what I wrote 64 Posts ago was in fact the case? WHY JUST NOW? WHEN THIS IS THE FIRST THING I TOLD YOU TO CHECK?

Lite is fine for all coding.

At this point, i have no idea what is cause of Chassis Stabilization Malfunction. Normally it comes from missing or corrupt DME CAFD i,e, (cafd_ffffffff-255_255_255), If that is case, you need to inject CAFD into DME and VO Code it:

Connect => Read FA (VO) => Activate FA (VO) => Read (ECU) => Left-Click on desired DME => Click on "Detect CAF for SWE" => Select the CAFD from latest I-Level shown (bottom one) => Select OK => Right-Click on DME (the ECU itself not the underlying CAFD) => Select CODE.

* NOTE: Motor can NOT be running when you code DME module.

* NOTE: Injecting CAFD (Detect CAF for SWE) and Flashing ECU's with >= v.4.17.20 PSdZData requires using newer E-Sys 3.30.0 or higher.

To fix errors, coding must be fixed. If DME has missing or corrupt CAFD (i.e. cafd_ffffffff-255_255_255), you need to Inject CAFD and VO Code DME as I wrote above,

 

Shawn, don't get mad please. I did it. Now DME has CAFD. For some reason, I couldn't get this last module ZGW to have CAFD. So each module supposed to have at least 1 CAFD ?

 

You did it...64 posts later. Yeah, I'm irritated. You wasted a lot of my time.

No. ZGW does not have CAFD. Leave it alone.

 

I check VIN on two diferent VIN decoder

S8SC​

Telematics Access Request,Country-Spec.​

 

I check VIN on two diferent VIN decoder

Not according to FA from BMW server.

 

Morning Shawn. This morning as soon as I started the car. The Chassis Stabilization Malfunction error shows instantly.

 

Clear Fault Codes:

With E-Sys:

Click "External Applications" in the left menu.
Click "External Application"
Double-click "Transmitter"
Scroll to the bottom and click "14 FF FF FF,31 01 0F 06,31 01 40 00 00,31 01 40 00 05,31 01 40 00 01;Clear all DTCs (clear DTC,clear Infospeicher,ZFS – DM_Lock,clear ZFS – DM_Clear,ZFS – DM_Unlock)"
Click Connect
Click Send

 

Ok thanks

 

Shawn, just curious how do you know this so good in and out? You are a master bmw mechanic?

 

No, I work in Oil & Gas. I am no mechanic at all.

 

Shawn, I just tried it a few times. Once I drive the car, that error comes back again. Do we have an alternative way to fix that? Do you think that module is broken? Its the hardware ?

 

Shawn, I just tried it a few times. Once I drive the car, that error comes back again. Do we have an alternative way to fix that? Do you think that module is broken? Its the hardware ?

Did you ever VO Code DSC with same FA?

 

Shawn, I just want to clarify this step. After I click on Clear all DTCs. I click connect, then hit send.
The program started to run and I 5 lines of === request. After that it stopped but I don't see anything saying its been cleared.
Should I wait little longer then hit Disconnect or after the 5 lines , it means cleared?

 

Shawn, I just want to clarify this step. After I click on Clear all DTCs. I click connect, then hit send.
The program started to run and I 5 lines of === request. After that it stopped but I don't see anything saying its been cleared.
Should I wait little longer then hit Disconnect or after the 5 lines , it means cleared?

Try changing Tester Address to F5 and running it again.

 

Just read this whole thread and just want to congratulate @shawnsheridan patience levels!

 

Hi @shawnsheridan

I am trying to reset my NBT_EVO unit back to the default settings as I am now unable to use Bimmercode. I understand I can use VO code to do this. What are the steps for this?

Also (probably a dumb question) If/when I do reset it back to factory defaults will it still be the same versions I currently have (NBTevo_Y21432J)

Thank you!

VO Coding will not change Firmware version. PM sent.

 

Ditto on this.. I know this thread is old but my god this man has the patience of a wise monk

 

@shawnsheridan
Hello shawn, I am really new to all this stuf, I have F20 2012, and want to disable stop and go, and enable digital speed to always on.
I have windows pc with e-sys 3.32.1 installed and psdzdata v.4.42.32.
Could you kindly please give me the simplest and easy steps to code these two options!
I read already a lot of posts but I don’t know if I have to do all of their steps in my case.

 

@shawnsheridan
Hello shawn, I am really new to all this stuf, I have F20 2012, and want to disable stop and go, and enable digital speed to always on.
I have windows pc with e-sys 3.32.1 installed and psdzdata v.4.42.32.
Could you kindly please give me the simplest and easy steps to code these two options!
I read already a lot of posts but I don’t know if I have to do all of their steps in my case.

FDL Code:

FEM_BODY => TCM_MSA_DEFAULT_OFF = aktiv
KOMBI => BC_Digital_V = aktiv

FDL Code = Coding of individual FDL's in an ECU, overriding the VO Coding.

Connect => Read FA (VO) => Activate FA (VO) => Read (ECU) => Right-Click on the ECU CAFD and select Read Coding Data => Expand the CAFD Folder by clicking + symbol => Right-Click on the CAFD file and select Edit <SvtCompareView.edit.fd.name> => Edit CAFD as desired => Click the Blue Floppy Disc Icon to Save CAFD => Click the green back arrow icon => Right-Click on the CAFD file => Select FDL CODE.

 

Hi Shawn,
bimmerutility, tnx v easy to use, does not show mirror in / out speed settings

an earlier thread suggested this may be possible using VO coding
how can i be sure VO is able to change the speed settings ?

tnx
Simon

 

Hi Shawn,
bimmerutility, tnx v easy to use, does not show mirror in / out speed settings

an earlier thread suggested this may be possible using VO coding
how can i be sure VO is able to change the speed settings ?

tnx
Simon

What mirror in / out speed settings are you looking for?

 

see below:

BDC_BODY
3110
ASP_GESCHWINDIGKEIT_AUTO_AUSKLAPPEN
(Value in HEX)needs to be set to hex 50 = 50 MPH / 80.5 KPH

BDC_BODY
3110
ASP_MAX_GESCHWINDIGKEIT_BEIKLAPPEN FF
(Value in HEX)needs to be set to hex 50 = 50 MPH / 80.5 KPH

these not visible on esys or bimmerutility

 

These codes exist in older FEM_BODY. I do not see them in BDC_BODY, and there is no VO Code that will work for this.

 

tnx Shawn

even if i find a friendly BMW tech, just not possible ?

 

If equivalent FDL Codes do not exist in BDC, then it is Game Over.