Hello!

Could be the same like F10
EGS/3000 Applikation/LC active

CU Oliver

 

any detail? link or something, thx

 

EGS/3000 Applikation/LC active is the details

 

hah
is that work actually?

 

Hello!

Try it. On a F31 it was the solution to activate the LC, also on a 535d F10. Both with 50.2.

CU Oliver

 

Launch Control

Hello!

Try it. On a F31 it was the solution to activate the LC, also on a 535d F10. Both with 50.2.

CU Oliver

Hi,

I have 320d and on egs/3000 Applikation, 02 there are only UNBELEGT,Segeln,MSA,Sportschalter_alt,NIC_alt,Sportschalter,Allrad,Vmax,MAB Variante,Stop/Go,UNBELEGT but there is no LC. Could it be somewhere different.

Thanks.

 

Hello!

You have to have the sport automatic gear and as I know 50.x at minimum.

CU Oliver

 

I coded the car, but it doesn't work either... The car doesn't have sport+ option. Can the failure be affected by this missing?

 

I think this function only works on cars have 2TB or Sport Gearbox option only.

 

my car has the sport program for the gearbox, but no paddles. Is it Sport Gearbox?

 

Hello!

No. Only with paddles you have it.

I've here the German version to switch on the LC. I can translate it later on.

CU Oliver

 

Hell!

Here is the German version.

CU Oliver

 

I can do something in coding to activate it anyway? Can I put 2TB in the option and recode the ecu? Or I will brick it?

 

Bricking comes from flashing ECU's, not coding them.

It was written above that LC requires N63 motor (.50) to work though but your 640i has N55 motor.

 

No, im talking about a F07 2.0d LCI I have now since my F13 4.0d in broken... I would like to code the LC on the car. I have the gearbox without paddles, but with Sport mode and manual changing. Do you have any suggestiones? FA Code?

 

Sorry, but I don't. I have not looked into LC at all.

 

what happen if I VO code 2TB on my car?

 

I can't say for sure. You can try it though, it won't hurt anything.

 

Ok. I'll try. Wich is the code for standard gearbox?

 

ok. I'll try. Wich is the code for standard gearbox?

205.

 

fter changed the VO, I don't have to write it ro the car, right?

 

No, you can just make it, load it in Coding module, and code with it, without ever writing it to the car.

 

Whay do you mean load in coding module?

 

Hit the Load button in the normal coding module and load it to code with it.

 

Hello!

It depends also on the i-level you have. Which one is yours?

CU Oliver

 

Translated from italian instructions:

For all the range 1 Series, 3 Series and 6 Series (from July 2013) it will be possible to have in combination with the 8-speed automatic transmission, the new Launch Control system, which in the past has been the preserve only of the variants Motorsport.
To use this function, the driver must activate the DTC mode (via the DSC button), place the gear lever in S, lift your foot off the brake and simultaneously presses the accelerator pedal all the way. The growth speed of the system of locks only when the driver lifts his foot off the gas slightly which will make a flying start without skidding the tires.

 

Hello!

I've coded the LC on a F10 535d (03/13) this day. The car has now the 50.2 and it was possible to code. With the old 49.3 there was no way.

CU Oliver

 

Did you need to flash EGS before with newest firmware or did you simply code the EGS using latest CAF file?

 

Hello!

Flashing of the car was done from the dealer (due to some problems with the brakes), I coded the EGS using the latest CAF.

CU Oliver

 

Thank you for starting this thread, I was trying to activate this on a 2013 650 Gran Coupe. There were 2 Launch Control Values that I found, one in the EGS module and one in DSC module. Coding didn't work so I believed it MIGHT be a limitation due to the software loaded onto the car. I'll check the car tomorrow and provide more specifics.

 

Tmrw we try again

Sent from BimmerApp mobile app

 

Hello!

As posted I coded it yesterday on a F11 535d. The guy tried it several times but the flag wasn't show. I can remember me that I need at minimum 20 tries to avtivate the LC on my M5 (I pressed the brake to hard - it's different to the LC on a normal F10/F11).

Now we have two options:
1. It can be coded but it will not work
2. It can be coded and it will work but it's not easy to activate it

CU Oliver

 

Aren't there different gearboxes on the new cars that have LC? I believe this is the case for the M135i, cars after 7/13 have Launch Control AND a different part number for the 8sp transmission.

 

Here's the data from the 650:

I Level is F010-13-03-505 so 49.4

The values changed are as follows:

DSC2/3000 Allgemein/Funktion_LaunchControl_aktiv
change to aktiv

EGS/3000 Application/LC
change to aktiv

The Integration Level is too old but something to test on a car that has 50.2

 

any news?

 

If you have a iPhone and recently flashed your 2013 to 50.2, can you check something for me?

Push and "hold down"" the voice command button and see if Siri answers??

Many thanks!

 

I will test it immediatelly after getting the latest software on saturday.

 

Hello

@Travel4Surf: i have a X3 F25 from 05.2013 and now update to 50.4. After that, the voice command to siri dont work. I have code the HU_NBT with change Zeitkriterium in the VO from 04.13 to 08.13, after that, the voice command hold function is working.

Chris