EDIABAS,ini should be INTERFACE = ENET, not REMOTE.

 

i change and nothing

 

No idea. Is Windows Firewall / Defender Disabled?

 

windows 7 yes i block firewall, i dont know whats problem...all day i thinking what to do

 

In ISTA Settings, what is your Vehicle Interface / VCI Config Interface Type set for?

 

i use enet local area network than i truy with enet direct connect and also enet area and isis network and nothing the same error....

 

It should be second Option, and then make sure EDIABAS.ini set for INTERFACE = ENET.

 

i truy and the same problem. i put already enet in ediabas manual open in notepad and change interface ENET. and choice ediabas in ista and same error ...but look this in ediabas from rheingold, evupath simulationpath is c:/ediabas/ecu, but my ediabas is in c:/rheingold/ediabas not on root c:/

 

Can you connect to car with Tool32 and ENET Cable?

 

didnt try and i dont have tool32. i can connect ista p before i work something in ista p and ista p work, cable is ok. i have also d can cable and try but nothing.

 

You used ENET Cable with ISTA/P? Must be very old version of ISTA/P as ISTA/P is now for E-Series ony.

Install run Tool32 and see if you can get it working with ENET Cable. If it can connect, then ISTA should be able to.

 

u mean bmw standard tool. i use before inpa and its work....

 

If INPA worked with ENET than ISTA should too.

ISTA has it own EDIBAS.ini. Are you setting it for ENET and not your Standard Tools EDIABAS.ini?

 

yes,i open rheingold and go to ediabas.ini and manul change interface ENET and go to insta and choice ediabas....i will check now with tool32....

 

Tool32 uses different EDIABAS. Testing with it will only prove Firewall is not blocking and Cable is good.

This is the ,ini that matters for ISTA:

C:\Program Files (x86)\BMW\ISPI\TRIC\ISTA\Ediabas\BIN\EDIABAS.INI

Not C:\Ediabas\BIN\EDIABAS.INI

 

i have only C:\Rheingold\Ediabas\BIN\ediabas.ini not program files....u give me ista and i just unzip all files on c root

 

That is correct folder for Standalone ISTA.

 

ista is ok. i change laptop and now is ok. with dell laptop no waay to connect to car....
but when i start vehicle test i recieve the programming system could not be initialised. the ista installation may be damaged .... but i click ok and i recieve faulty codes....

 

do u know can i with enet cable do some code on my car, i must switch off pads on wheel

 

Can code with ENET Cable and E-Sys Package.

 

aha. do u have ista d to download and esys...thanks bro for help....real thanks a lot....

 

I cannot help with ISTA. PM sent.

 

in esys i can switch off some function on car?

 

Yes.

 

thanks bro

 

Hi.
Would anyone be willing to help make Enet work with ISTA D? I tried all the procedures from the forum but without success.
ISTA starts but does not connect to the car (F45). The error is displayed: The vehicle could not be identified successfully. Check vehicle interface and 'PAD active'.
I tried:
Edit EDIABAS.INI (enet)
Edit the registry (online mode true)
Set the IP address in the network adapter settings

Today I installed EasyBMWTools, but even Tool32 does not communicate.

The laptop network adapter is working properly. I measured Enet with a multimeter, it looks OK.

Thanks.

 

Is ethernet adapter set as dynamic? Ediabas is not important for ENET. Is Esys showing VIN and IP and can connect?