BMW Forum - BimmerFest BMW Forums banner
Cancel
Create thread New Garage Forums

PSdZData FULL Requests (Programming Firmware)

Fxx-/Ixx-/Gxx-series
Jump to Latest
1.1M views 11K replies 3.9K participants last post by  shawnsheridan  
#1 · (Edited by Moderator)
Hello,

I have version 57.3

Is there a newer version?

What is the newer version?

What does it give over the older version?

Most important, is it needed for a 2016 M3?
 
  • Like
Reactions: stiga77, SamuraiAU, VengeanceDemon and 17 others
Save
Reply Quote Like Like
K
#4,382 ·
Shawn thanks again for the link.

Btw, i tried to read all ecu with psdzdata v4.21.12
But still couldn't find the HU_MGU file, cafd_00003E52-006_022_027

The swe\cafd directory only got cafd_00003E52-006_022_025

Does it mean i have to wait for the next psdzdata version?

P.S. Back to dealer 2 weeks ago and they did system update...
 
G
#4,384 ·
Hi Shawn,

Can you send the link for latest Psdzdata Lite?

Additional question:

Reference: ESys, official TM Launcher 3, F82 M4

When I open Connect dialog I see 2 entries for F020. One of them is greyed out slightly but I can still connect using either of the two entries.

Any ideas why I am seeing 2 entries for same chassis? What does the grey option indicate?
As indicated, I can select either entry and I can establish a connection and read FA.
Some insight would be helpful...
 
#4,385 ·
PM sent.

Two I-Steps is now normal due to changes in ISTA. With ISTA 4, it is possible to set an execution stop for specific series, equipment, etc. even after installation. This make it possible to specifically prevent vehicles in the Retailer Organisation from being updated with problematic software. From ISTA 4.13.1x, the affected vehicle can be treated in certain cases with an alternative (older) I level.

Pick bottom (newest) one.
 
Save
Reply Quote Like Like
G
#4,387 · (Edited)
Thank you, much appreciated.

--- IGNORE BELOW -- ALREADY RESOLVED WITH HELP OF SHAWN ----

I am trying to FDL code FEM_Body module on a F82,M4.

Trying to set the auto start stop and a few other values.

ESys does not report any errors; states 0 errors at end of process - appears to have coded the values.

However, the values are not changed. They are exactly as default.

If I read the FEM_Body back, the values are as default, they have not changed.

The only error (while being FDL coded) I see is on the iDrive screen which says "Front End Colission disabled...." This error too disappears after FDL coding is finished.

I have been FDL coding for a while, and have never encountered this issue.

The only difference I can think of is that my car now has a flash tune via BootMod3 and GTS transmission flash done via BootMod3.

I even reverted back to stock transmission flash and stock flash using BootMod3; then tried to FDL code the FEM module, but same problem.

The FDL coding does not stick...

I am attaching the log files and CAFD if it helps... (added PDF extension just upload)
Click to expand...
 

Attachments

#4,389 ·
gspannu said:
Thank you, much appreciated.

I am trying to FDL code FEM_Body module on a F82,M4.

Trying to set the auto start stop and a few other values.

ESys does not report any errors; states 0 errors at end of process - appears to have coded the values.

However, the values are not changed. They are exactly as default.

If I read the FEM_Body back, the values are as default, they have not changed.

The only error (while being FDL coded) I see is on the iDrive screen which says "Front End Colission disabled...." This error too disappears after FDL coding is finished.

I have been FDL coding for a while, and have never encountered this issue.

The only difference I can think of is that my car now has a flash tune via BootMod3 and GTS transmission flash done via BootMod3.

I even reverted back to stock transmission flash and stock flash using BootMod3; then tried to FDL code the FEM module, but same problem.

The FDL coding does not stick...

I am attaching the log files and CAFD if it helps... (added PDF extension just upload)
Click to expand...
All I can say is be sure you use Code FDL, and not CODE, and it must complete without error(s).
 
Save
Reply Quote Like Like
#4,396 ·
I cannot help with ISTA (sqlite databases).

If you have Full, there is Zero reason to also have Lite, and not that you would ever need it, but you could just make Lite from full. PM sent.
 
Save
Reply Quote Like Like
B
#4,400 ·
Hi Shawn

I just received my GO5 M50i last week.

I have E-Sys Premium Launcher 2.8.2.155 up and running with E-Sys 3.27.1 utilizing PSdZData_Lite v 4.20.30.

Upon launching Premium Launcher I select G005 then it opens E-Sys 3.27.1.

I connect to the car OK, then select S18A which indicates it covers G005.

However I cannot find ANY for these examples.

</cafd>
<cafd id="000044ED" name="BDC_BODY3" author="jokinawa" series="S18A">

Code: 
			<group id="3510">
				<function start="11" end="11" comment="FH_KOMFORTSCHLIESSUNG_FB" mask="00100000b">aktiv</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">nicht_aktiv</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">bremslicht_blinkend</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">flaechenvergroesserung</function>
			</group>
</cafd>
<cafd id="00002742" name="DME_BAC2" author="jokinawa" series="S18A">

Code: 
			<group id="3020">
				<function start="19" end="19" comment="TCM_MSA_MEMORY" mask="00000010b">01</function>
			</group>
[/CODE]
Code: 
			<group id="3001">
				<function start="18" end="18" comment="LOGO_SCHRIFTZUG" mask="11111111b">m_logo</function>
			</group>
			<group id="3000">
				<function start="53" end="53" comment="GLOBAL_LAYOUT_VARIANTE" mask="11110000b">m_gmbh</function>
			</group>
ETC. ETC.

I am wondering if the X5 M50i has different mapping to the other GO5s? Or is there a different version of software I should be using?

Thanks and sorry for the bother.
 
B
#4,401 ·
Hi Shawn

I just received my GO5 M50i last week.

I have E-Sys Premium Launcher 2.8.2.155 up and running with E-Sys 3.27.1 utilizing PSdZData_Lite v 4.20.30.

Upon launching Premium Launcher I select G005 then it opens E-Sys 3.27.1.

I connect to the car OK, then select S18A which indicates it covers G005.

However I cannot find ANY for these examples.

</cafd>
<cafd id="000044ED" name="BDC_BODY3" author="jokinawa" series="S18A">

Code: 
			<group id="3510">
				<function start="11" end="11" comment="FH_KOMFORTSCHLIESSUNG_FB" mask="00100000b">aktiv</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">nicht_aktiv</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">bremslicht_blinkend</function>
			</group>
Code: 
			<group id="3075">
				<function start="1" end="1" comment="GEFAHRENBREMSLICHT_TYP" mask="01100000b">flaechenvergroesserung</function>
			</group>
</cafd>
<cafd id="00002742" name="DME_BAC2" author="jokinawa" series="S18A">

Code: 
			<group id="3020">
				<function start="19" end="19" comment="TCM_MSA_MEMORY" mask="00000010b">01</function>
			</group>
[/CODE]
Code: 
			<group id="3001">
				<function start="18" end="18" comment="LOGO_SCHRIFTZUG" mask="11111111b">m_logo</function>
			</group>
			<group id="3000">
				<function start="53" end="53" comment="GLOBAL_LAYOUT_VARIANTE" mask="11110000b">m_gmbh</function>
			</group>
ETC. ETC.

I am wondering if the X5 M50i has different mapping to the other GO5s? Or is there a different version of software I should be using?

Thanks and sorry for the bother.
 
#4,414 ·
Hey all, I am trying to code my daughter's X1. It has F056-17-11-531. I tried with esys 3.29 and Psdzdata (I am not quite sure about used version) but I get Psd error.
I searched the web and my understanding is that I MUST use at least 3.63.2 version. Is this correct?
I also understood that something has changed since psdz 3.62 about the possibility to code the ECU's but I am not sure about it.
I kindly ask for link to download Psdz 3.63.2 or higher and any useful hint for coding.
Thank You for your assistance.
 
#4,425 ·
Save
Reply Quote Like Like
BMW Forum - BimmerFest BMW Forums
posts
12M
members
799K
Since
2001
A forum community dedicated to BMW owners and enthusiasts. Come join the discussion about Bimmerfest events, BMW production numbers, programming, performance, modifications, classifieds, troubleshooting, maintenance, and more! Bringing the BMW community together.
Full Forum Listing
Explore Our Forums
E90/E91/E92/E93 (2006 - 2012) E39 (1997 - 2003) E46 (1999 - 2006) E36 (1991 - 1999) E60 / E61 (2004 - 2010)